Appliance Headers...again

bbbentley · #1 07-09-2017, 03:31 AM

I just acquired these headers. I read up what I could about Appliance from other posts. I am hoping the more experienced on here can tell me more? Like how old these may be? Are they Appliance (consensus)? and, where is the part number located? They are for a BBC. Guy I got them from said they were either on his 67 Chevelle or his 68 Camaro, but could not remember?

**Day2_69Z** · #2 07-09-2017, 04:14 AM

Most likely Appliance.
More than likely Chevelle vs Camaro.
The right side (passenger side) has tubes past the flange end towards the firewall where Chevelles have much more room.

**1967Z28** · #3 07-09-2017, 03:22 PM

This link shows Appliance headers for Chevelle plus where the p/n is stamped. Yours are close but not exactly the same.

https://www.yenko.net/forum/showthrea...58#post1293358

I don't think they will work on a '67-'69 Camaro because of the #7 tube. It looks like it would interfere with a Camaro steeering box/pitman arm.

bbbentley · #4 07-09-2017, 03:31 PM

Quote:

Originally Posted by 1967Z28

This link shows Appliance headers for Chevelle plus where the p/n is stamped. Yours are close but not exactly the same.

https://www.yenko.net/forum/showthrea...58#post1293358

I don't think they will work on a Camaro because of the #7 tube. It looks like it would interfere with a Camaro steeering box/pitman arm.

Thank you. I read that post, but I did not see where the part number location was mentioned. And, I compared mine to those in the post, and mine are not like those in the post , agree.

**earntaz** · #5 07-09-2017, 03:50 PM

Quote:

Originally Posted by bbbentley

I just acquired these headers. I read up what I could about Appliance from other posts. I am hoping the more experienced on here can tell me more? Like how old these may be? Are they Appliance (consensus)? and, where is the part number located? They are for a BBC. Guy I got them from said they were either on his 67 Chevelle or his 68 Camaro, but could not remember?

Have to agree -- they look like Appliance ... TAZ

**whitetop** · #6 07-09-2017, 04:06 PM

Could also be early Mr Gasket or Blackjack-both had the square header flange. Blackjack still had the square header s flange well into the 80's.

Part number is either on the flange or down by the collector

bbbentley · #7 07-09-2017, 04:06 PM

Quote:

Originally Posted by bbbentley

Thank you. I read that post, but I did not see where the part number location was mentioned. And, I compared mine to those in the post, and mine are not like those in the post , agree.

Never mind. I see now where the part # is. Even a blind hog gets lucky and finds an acorn once in while!

Edit: Ok, found what I was after. Much thanks to all and thank you Jon, Taz others. By the number found! and comparing to the catalog, it is Appliance and for 1970-1 Camaro BB.

**earntaz** · #8 07-09-2017, 06:08 PM

Triple B -- here is a shot of the RH Appliance for my 70' Nova ... TAZ

**mockingbird812** · #9 07-10-2017, 11:30 AM

Great shot TAZ. A man and his engine!

**Mr70** · #10 07-10-2017, 01:19 PM

Quote:

Originally Posted by bbbentley

By the number found! and comparing to the catalog, it is Appliance and for 1970-1 Camaro BB.

Let us know if you post these up for sale.

The Following User Says Thank You to 1967Z28 For This Useful Post:
bbbentley (07-09-2017)

The Following User Says Thank You to earntaz For This Useful Post:
bbbentley (07-09-2017)

The Following User Says Thank You to mockingbird812 For This Useful Post:
earntaz (07-10-2017)