'70 Camaro Fan Shroud

[47Hammer]

I'm looking for the correct fan shroud without the caution fan stamped in it. http://www.yenko.net/ubbthreads/images/graemlins/biggthumpup.gif

[70 copo]

I think I have one. Send me a PM.

Phil

[47Hammer]

Done!

[Kim_Howie]

Not to steal the post but I am looking a 6-poper shroud VO1 opt. ?? http://www.yenko.net/ubbthreads/images/graemlins/beers.gif

[CamarosRus]

Kim, Camaro white Book says VO-1 was Heavy Duty Radiator. Please educate us with what you know of this VO-1 option and if same as came with Big Blocks and ONE piece shroud (VERY Rare ending with #920)

[Rick H]

RPO VO1 is the same radiator used on Z/28 and V8 cars ordered with A/C. VO1 was included when Z/28 ordered.

Kim, your top radiator support panel that holds the shroud should be extended to the drivers side . Same as Z/28. So your should would be the same as the Z/28.

I have both base and Z/28 shrouds and panels if you want me to post them.

Rick H

[Kim_Howie]

Chuck,Enclosed pics from factory man.

[Kim_Howie]

2nd pic

[Kim_Howie]

3rd pic

[Kim_Howie]

Notice the difference in my 6 cyl. plate and a small block plate.

[Rick H]

Kim,
My top panel off my Z is part number 3973904. I am looking at it while I type this.

The shroud that fits it is the two piece shroud with part numbers 3973912 and 3973910. As I mentioned it is the same as Z/28 which came with VO1 when ordered.

I don't have an extra one.

Rick H.

[Kim_Howie]

Enclosed is org picture of my car taken 1970 Notice the plate and shroud.I think they are different than the v8 plate and shrould. I have the org. plate on my car and the part # stamped in it is the same as the VO1 # 3973904 This what I am looking for. Kim P.S. my car was a 6cyl. to start with.

[Kim_Howie]

Same plate 35 years later!!!

[Kim_Howie]

org. sticker 35 years later

[Rick H]

Kim,
The 6 cylinder and non-AC cars had the smaller top panel and shroud as shown in your picture.

The Z/28, V8 cars with A/C and special order VO1 option had the 3973904 top panel and 912 and 910 two piece shroud.

Also look on your top plate next to the part number. Is there a letter before the number? My 3973904 panel off my Z has an "L" before the number.

If I get a chance tomorrow I will get pictures of both the standard panel and shroud and the VO1 option panel and shroud.


Kim after looking at your picture you need the 2 piece 912 and 910 shroud. If you are not looking for original you can get the 2 shroud pieces through GM. Approx $45.00 each piece.

Rick H.

[Kim_Howie]

Rick, The bottom shroud you can still buy from Chevy. I have one of them. I bought a year ago but not the top one. The V8 upper part # is 3973900 and for the 6 cyl. is part # 3972910 I think they are different. I have several that I have bought on the internet thinking they were close by their pictures they posted, So far none are the 6 cyl. one. Still looking. Kim http://www.yenko.net/ubbthreads/images/graemlins/beers.gif

[Kim_Howie]

Rick I will check the 912 #

[Kim_Howie]

Rick, pictures would be great thanks Kim http://www.yenko.net/ubbthreads/images/graemlins/worship.gif

[Rick H]

Kim,
3973900 is the upper shroud piece for non-A/C cars. The lower shroud would be 3973902. Also NOT found on Z/28 or cars with VO1.

The correct VO1 and Z/28 shrouds would be 3973910 and 3973912. This is what you want if running a V8.

I'll grap both my shrouds tomorrow.

Rick H.

Rick H.

[70-SS/RS-L78]

I don’t mean to hijack this thread but I also need a 70 Z/28 shroud without the Caution Fan
If anybody has a nice one for sale send me an email.
Thanks
[email protected]

[Rick H]

Kim,
See my post under technical and restoration under help with 2nd gen Camaro fan shroud.

Rick H.

[SMGCO]

[ QUOTE ]
I'm looking for the correct fan shroud without the caution fan stamped in it. http://www.yenko.net/ubbthreads/images/graemlins/biggthumpup.gif

[/ QUOTE ]

I've got one in my shorts for you Bart.

[47Hammer]

Thanks Steve, But i'm not looking for the mini-version or aftermarket. I need full size and correct version only. Make sure you call me when the COPO hits the road. http://www.yenko.net/ubbthreads/images/graemlins/3gears.gif I'll be able to hear that thing from my house, huh?
Happy New Year! http://www.yenko.net/ubbthreads/images/graemlins/biggthumpup.gif