Forum: Supercar/Musclecar Discussion
06-09-2024, 02:08 PM
|
Replies: 10
Views: 1,001
|
Forum: Technical & Restoration
05-08-2024, 03:16 PM
|
Replies: 11
Views: 1,792
|
Forum: Lounge
04-27-2024, 03:44 PM
|
Replies: 38,865
Views: 9,360,205
|
Forum: Supercar/Musclecar Discussion
04-05-2024, 01:04 PM
|
Replies: 29
Views: 4,048
I guess you could always do this: ...
I guess you could always do this:
https://carlisletyrfil.com/products/tyrfil-flatproofing/
and just put them on for the shows.
Seems like it would take the explosion risk out of the picture. ...
|
Forum: Supercar/Musclecar Discussion
03-20-2024, 10:56 PM
|
Replies: 19
Views: 3,874
|
Forum: Technical & Restoration
03-20-2024, 01:08 PM
|
Replies: 9
Views: 1,593
|
Forum: Technical & Restoration
03-19-2024, 12:32 PM
|
Replies: 9
Views: 1,593
|
Forum: Technical & Restoration
02-21-2024, 02:50 PM
|
Replies: 6
Views: 1,039
In case you want to "roll your own"
Made...
In case you want to "roll your own"
Made mine on a CNC mill using an old transfer punch, but a lathe may work.
The rivets I got from my local TrueValue hardware store in the Hillman stuff:
...
|
Forum: Technical & Restoration
02-20-2024, 12:08 PM
|
Replies: 23
Views: 2,605
|
Forum: Technical & Restoration
02-17-2024, 04:07 PM
|
Replies: 8
Views: 1,587
|
Forum: Technical & Restoration
02-17-2024, 02:02 PM
|
Replies: 8
Views: 1,587
You'll get many answers on this, but for me I...
You'll get many answers on this, but for me I went basic with SPI epoxy primer top coated with a flattened Delfleet Essential black urethane. Sounds like a great car. The red Koni's are definitely...
|
Forum: Technical & Restoration
02-15-2024, 08:51 PM
|
Replies: 11
Views: 1,863
|
Forum: Technical & Restoration
02-15-2024, 05:20 PM
|
Replies: 11
Views: 1,863
|
Forum: Technical & Restoration
02-15-2024, 04:36 PM
|
Replies: 11
Views: 1,863
|
Forum: Supercar/Musclecar Discussion
01-04-2024, 03:26 PM
|
Replies: 92
Views: 52,683
|
Forum: In Memoriam
12-27-2023, 05:22 PM
|
Replies: 7
Views: 1,413
|
Forum: Vintage Certification
11-21-2023, 12:38 PM
|
Replies: 48
Views: 16,604
|
Forum: Lounge
09-28-2023, 01:18 PM
|
Replies: 4
Views: 1,579
Cool engine and lots of tech there, but not as...
Cool engine and lots of tech there, but not as visually impressive as the cutaways from the 60's and 70's where the model shops really cut things and chromed and painted the internals. This one is...
|
Forum: Lounge
09-13-2023, 12:41 PM
|
Replies: 38,865
Views: 9,360,205
Is that really the same car? The body line on...
Is that really the same car? The body line on the fender back to the door looks completely different. Much deeper on the restored car. Look at the rear door edge. Looks like they took a sedan and...
|
Forum: Other Events
09-08-2023, 12:28 PM
|
Replies: 6
Views: 11,910
|
Forum: Supercar/Musclecar Discussion
09-06-2023, 08:03 PM
|
Replies: 9
Views: 2,200
Knowing what little I do about industrial...
Knowing what little I do about industrial plating, there are coatings (think grease-like substances) that can be applied to mask the area where you do not want the plating to occur. These are then...
|
Forum: Other Events
09-05-2023, 03:49 PM
|
Replies: 6
Views: 11,910
Gathering of the Geezers - Kil Kare
If you are in the Dayton-Xenia Ohio area, this Sunday the 10th is the annual Gathering of the Geezers car show and race event. Usually a pretty good turn-out. It's the 15th year for this....
|
Forum: Technical & Restoration
08-25-2023, 12:41 PM
|
Replies: 3
Views: 1,269
One problem is the DOT regulations have changed...
One problem is the DOT regulations have changed since the 1960's early 70's to mandate the double crimp on the end pieces, so nobody can legally sell a new part with the original single crimps. Even...
|
Forum: Supercar/Musclecar Discussion
08-22-2023, 03:29 PM
|
Replies: 28
Views: 8,003
|
Forum: Technical & Restoration
08-11-2023, 01:19 PM
|
Replies: 16
Views: 4,112
|