Re: 72 TA : New Project
 

Rick,

Yes, that's the one!

I PM'd you my address and I'll add you the the ever-expanding list of invitees to the who-knows-when, unveiling of the car!

At this rate I should just sell time shares in the passenger seat.

[img]<<GRAEMLIN_URL>>/beers.gif[/img]

Re: 72 TA : New Project
 

Fusick Automotive (Olds vendor) sells those clips individually. Male and female end right, wraps around the wire and then snaps together? Wire harness tie down strap, PN 3728 1.50 each.

Re: 72 TA : New Project
 

Hood finaaly in paint and awaiting wetsanding:

http://i466.photobucket.com/albums/r...s72hood002.jpg

http://i466.photobucket.com/albums/r...s72hood001.jpg

http://i466.photobucket.com/albums/r...s72hood003.jpg

Re: 72 TA : New Project
 

Is that the final piece of the puzzle? Can't wait to see the pictures of the finished product.

Re: 72 TA : New Project
 

Actually the polyethylene front valance will be the last body piece of the puzzle when it gets done...and then getting the hood section of the stripe decal that has been on freakin' back order since last September and I am not happy about that.

I can just see the car being all done and not having that decal section, still.

[img]<<GRAEMLIN_URL>>/rolleyes.gif[/img]

Sorry for the rant [img]<<GRAEMLIN_URL>>/blush.gif[/img]

Hopefully, I'll be picking up the beak this weekend and updating the never-ending story.

Re: 72 TA : New Project
 

Rick,

Thanks for the wiring clip. It arrived today and that was the right one. [img]<<GRAEMLIN_URL>>/beers.gif[/img]

Re: 72 TA : New Project
 

Picked up the beak today and installed it. The 70-72's are pretty easy. The 73's are the hard ones since they have a ton (literallly) or extra 5 mph impact bracing inside the nose.

I just attached the little bracket do-hickies to the inside of the nose and then hung it in place with the bolts. The beak lined right up. I guess all that playing and realigning of the fenders a few months back, worked out well.

The real trick is to have the car jacked up by two floor jacks under the rear of the subframe. You want the front wheels to be off the ground and hanging. This way the front of the car is warping down. You attach the urethane nose, line it up and bolt it down. Then when you let the car off the jacks, it pulls the urethane nose closer to the fenders. If you try to attach the urethane nose while the car is on the ground, it tends to leave a gap between the fender edges and the nose.

I then took her for a ride around town. Definitely have to get used to these low revving Pontiacs. They don't seem to rev up very fast but they do have a ton-o-power! It was fun to see the shaker working, too, when you stomp the gas pedal.

http://i466.photobucket.com/albums/r...b/S7005249.jpg

http://i466.photobucket.com/albums/r...b/S7005247.jpg

http://i466.photobucket.com/albums/r...b/S7005248.jpg

Re: 72 TA : New Project
 

I love the EARLY 2nd Gen T/A's ABSOLUTELY STUNNING!

Re: 72 TA : New Project
 

Looking great Steve! When is the next car show you are going to attend? My orange car should be ready to cruise soon and I will be looking for places to drive it [img]<<GRAEMLIN_URL>>/smile.gif[/img]

Re: 72 TA : New Project
 

Likely one of the best threads ever on this site and a joy to watch the progression. Great job Steve!