Dedicated to the Promotion and Preservation of American Muscle Cars, Dealer built Supercars and COPO cars. |
|
|||||||
| Register | Album Gallery | Thread Gallery | FAQ | Community | Calendar | Become a Paid Member | Today's Posts | Search |
|
|
|
Thread Tools | Display Modes |
|
#1
12-07-2022, 10:19 AM
|
||||
|
||||
Chassis Semi-Gloss Recommendations
Back on the rotisserie, getting closer to paint. The painter recommended what he calls epoxy radiator black which is a pretty tough coating. I feel it’s a bit too glossy so any advice on a good product for the floor pans, subframe, wheel liners etc would be greatly appreciated. Jerry M’s book says 30% gloss for these items.
Additionally, I’m thinking gloss likely varied (as an example) between the subframe and floor pans as I assume the subframes came into the plant pre-painted. Is this a correct assumption? 
|
|
#2
12-07-2022, 12:37 PM
|
||||
|
||||
|
Paul,
I'd reach out to Lloyd and ask him what he is using. https://www.yenko.net/forum/member.php?u=51901 I looked through Chick's thread and did not see anything definitive as to what they used in his 68. https://www.camaros.net/threads/time...stored.182584/ Can't wait to see the continued progress! Tim
|
| The Following User Says Thank You to napa68 For This Useful Post: | ||
juliosz (12-07-2022) | ||
|
#3
12-07-2022, 02:05 PM
|
|||
|
|||
|
https://www.yenko.net/forum/showthre...=140219&page=3
There's all you need to know about correctly finishing the undercarriage on a 1st Gen Camaro. Starts at Post #23.
__________________
Learning more and more about less and less...
|
|
#4
12-07-2022, 02:41 PM
|
|||
|
|||
|
Wow, I just read a little of that post and I am saving it to read fully and follow all the steps! I have a 51 AD and my 69 vert to paint and was wondering what I need to do. Those post are just what I needed! Mike's thread as well as Lloyd's Brooklyn thread, and Chick 68 Z thread are all you need to restore Camaros!
__________________
69 SS 350 convertible (in peices) 69 327 convertible (driver)
|
|
#5
12-07-2022, 05:57 PM
|
|||
|
|||
|
Bill Hirsch paints are high quality (at least they were 15 years ago).
The chassis black has held up very well on my car. I don't know if you can get it in a rattle can. But for me, even if you can, I like to use a spray gun.
__________________
Don't believe everything you read on the internet ... Ben Franklin
|
|
#6
12-07-2022, 06:41 PM
|
|||
|
|||
|
Do they give full deduction points wise for using powder coat? It sure is nice and easy to mess with the sheens….
|
|
#7
12-09-2022, 08:00 PM
|
|||
|
|||
|
SPI Epoxy
Underfloor was done with SPI (Southern Polyurethane Inc) Black Epoxy
Notice the Sheen (Not Gloss by Semi Gloss) Firewall Was Top Coated with DELFLEET Essential Single Stage Polyurethane mixed to the semi Gloss Formula
__________________
Chuck Sharin [email protected] Auburn,WA (30 miles South of Seattle) 70 Camaro R/S Z-28, L-78, R/S SS 69 Camaro COPO "recreation"
|
| The Following 3 Users Say Thank You to CamarosRus For This Useful Post: | ||
|
#8
12-09-2022, 08:34 PM
|
|||
|
|||
|
----Love that "semi" sheen, Chuck!.....Bill S
|
|
#9
12-09-2022, 09:08 PM
|
|||
|
|||
|
not sure if you can still get it, but gm had "reconditioning" paint in the gallon, corect semi gloss not too long ago
|
| The Following User Says Thank You to 67ssmn For This Useful Post: | ||
juliosz (12-10-2022) | ||
|
#10
12-11-2022, 12:13 AM
|
|||
|
|||
|
MY above SPI underfloor not only looks GOOD but is catalized 2k EPOXY......What's the Quality of YOUR suggestion ????
__________________
Chuck Sharin [email protected] Auburn,WA (30 miles South of Seattle) 70 Camaro R/S Z-28, L-78, R/S SS 69 Camaro COPO "recreation"
|
|
|
|
Linear Mode
