Go Back   The Supercar Registry > General Discussion > Day 2 stuff-modified cars


Reply
 
Thread Tools Display Modes
  #601  
Old 02-18-2021, 04:31 AM
NorCam's Avatar
NorCam NorCam is offline
Senior Member
 
Join Date: Feb 2015
Location: Alberta, Canada
Posts: 4,190
Thanks: 2,583
Thanked 3,399 Times in 1,242 Posts
Default

You have to cut for the side of the shifter body to come through the side of the tunnel. The top of the body comes through about 2 inches and that protruding body then tapers down as the tunnel runs out towards the floor. The cut must run down below the lower tabs of the shifter body and then you have the 3/4 rod that attaches on the outer leg. That shift rod then needs the floor cut for at least 4"-5" forward of the shifter and it needs about 3/4" relief for the rod to not be in contact with the tunnel. I am sure you could pound that out with a big hammer, but I'd rather cut it than pound it out. Here's a picture that shows how much of the body is going to be sticking through.



I don't think the big block is that much different from a small block in terms of tranny positioning is it? Like maybe 1/4" or something? In either case, this shifter mount locates the body up high and needs relief cuts in the top of the tunnel and through the driver's side or the shifter isn't going to fit. You can maybe close it in tighter and negate making the box as I did, but then you need to wrap a large boot down and around the side of the tunnel which I don't like the looks of? Unfortunately, I didn't see any shortcuts in how to do this right and did what I could to close it in while keeping it neat.

The current model Super Shifters have smaller diameter shifter rods but they are weaker design than the older ones like I have here. I'm pretty sure the Super Shifters have always used this particular mount, but as I have done in the past, there are ways to mount it down low using a different mount and the lighter offset shift rods. That means less cutting but don't think the functionality is as good with those modifications.

FWIW...I'm no expert at this. Just doing what I can with what I have here and pretty happy with how it's turning out so far.
__________________
I like solid lifter cars, big cams and cars w/ 3 pedals in them.

Last edited by NorCam; 02-18-2021 at 02:06 PM.
Reply With Quote
  #602  
Old 02-18-2021, 04:37 AM
NorCam's Avatar
NorCam NorCam is offline
Senior Member
 
Join Date: Feb 2015
Location: Alberta, Canada
Posts: 4,190
Thanks: 2,583
Thanked 3,399 Times in 1,242 Posts
Default

Here's another shot from the underside as I was sizing things up. I started with a smaller cut and tried to hinge that side cut out to box in the shifter body along the bottom edge, but it wasn't going to give me anything to mount a new boot around so I later enlarged the hole and then built the box to close everything in. You can see from this picture that even the lower shift leg for 3/4 needs to go out beyond the tunnel side. They are a very invasive install as compared to anything stock. LOL

__________________
I like solid lifter cars, big cams and cars w/ 3 pedals in them.
Reply With Quote
The Following User Says Thank You to NorCam For This Useful Post:
dykstra (02-18-2021)
  #603  
Old 02-18-2021, 01:32 PM
njsteve's Avatar
njsteve njsteve is offline
Yenko Contributing Member
 
Join Date: Nov 2003
Location: NJUSA
Posts: 8,235
Thanks: 7
Thanked 2,378 Times in 752 Posts
Default

I did not know about the different offsets. And yes my pace car was a 350.
Reply With Quote
The Following User Says Thank You to njsteve For This Useful Post:
NorCam (02-18-2021)
  #604  
Old 02-18-2021, 05:22 PM
big gear head's Avatar
big gear head big gear head is offline
Yenko Contributing Member
 
Join Date: Mar 2012
Location: KY
Posts: 3,090
Thanks: 4,722
Thanked 1,111 Times in 633 Posts
Default

I think the Mr. Gasket V Gate and the Long shifters require an even larger hole, which is why I haven't installed one of them in my car.
__________________
Freddie
1969 Camaro RS/SS396 (427) 4 speed
Reply With Quote
  #605  
Old 02-18-2021, 08:10 PM
Ryan1969Chevelle's Avatar
Ryan1969Chevelle Ryan1969Chevelle is offline
Yenko Contributing Member
 
Join Date: Nov 2012
Location: Beautiful Elora Ontario Canada
Posts: 5,829
Thanks: 412
Thanked 685 Times in 393 Posts
Default

Love the shifter decisions!!


I personally love chaulk marks, and paint daubs, but I would cut up a floor in nearly any car to get a bad ass shifter in place.


This car with a stock shifter would have been a big miss in my opinion. I bet the shifter is the most fun item on the whole car, and each time you drive it you will be happy you cut some sheet metal the heck out of the way!!


I offer my Sawzall skills to any muscle car owners who want a big hole in the floor and can't bring themselves to do it. Not kidding.


Ryan W31.


This has motivated me to improve my shifter hump :-)
__________________


1969 Beaumont 350 Auto White Sold
1969 Beaumont 307 Auto Green Sold
1969 Chevelle SS 396-L35 Auto Blue Sold
1969 Oldsmobile Cutlass 'S' Sports Coupe W31
Reply With Quote
  #606  
Old 02-18-2021, 08:31 PM
3X24SPD 3X24SPD is offline
Yenko Contributing Member
 
Join Date: Oct 2020
Posts: 116
Thanks: 30
Thanked 185 Times in 52 Posts
Default

I never knew Hurst made another inline shifter besides the Vertigate. I also have a Mr. Gasket Vertigate, and that shifter is identical to the Hurst except for the script. I had to look up what makes a RamRod different than a Vertigate. Found a great pic to share.
Attached Images
 
Reply With Quote
The Following User Says Thank You to 3X24SPD For This Useful Post:
big gear head (02-18-2021)
  #607  
Old 02-18-2021, 08:42 PM
X66 714's Avatar
X66 714 X66 714 is online now
Yenko Contributing Member
 
Join Date: May 2009
Location: It's a dry heat, Arizona
Posts: 1,761
Thanks: 2,796
Thanked 1,036 Times in 422 Posts
Default

Hurst made the RamRod first. I used them for years when I was younger. Kind of a theft deterant. Most people that road with me didn't know how to work it...Joe
__________________
1968 Z/28 Corvette Bronze. Black Hounds Tooth. 02E Los Angeles born 3/13/1968 pnt OO
1969 SS396 Yellow/Yellow 08E Norwood born 8/28/1969 pnt 76E
1970 'cuda Moulin Rouge, 440-6, 4 speed
Reply With Quote
The Following User Says Thank You to X66 714 For This Useful Post:
jbtech (02-20-2021)
  #608  
Old 02-18-2021, 09:02 PM
rszmjt rszmjt is offline
Senior Member
 
Join Date: Nov 2004
Location: Calgary,Alberta,Canada
Posts: 263
Thanks: 5
Thanked 117 Times in 77 Posts
Default

Quote:
Originally Posted by 3X24SPD View Post
I never knew Hurst made another inline shifter besides the Vertigate. I also have a Mr. Gasket Vertigate, and that shifter is identical to the Hurst except for the script. I had to look up what makes a RamRod different than a Vertigate. Found a great pic to share.
Never owned a Ramrod or Vertical Gate. I did own 4 Hurst Super Shifters 1,s at 1 time, 1 had 4 Chrysler Liberty 4 speeds for my S/G car which I raced for 12 years. If we burred a Pro Shift Hub we could change the trans in 7 mins between rounds . Did that in 1990 @ Seattle. Never missed a gear in 12 years, they worked Mint, never saw the need for a Vertical Gate as they were big & clunky IMO.
That is world champion Mike Federer in the Penzoil roadster in the other lane.

Graeme, your going to love that shifter.
Attached Images
 

Last edited by rszmjt; 02-18-2021 at 09:05 PM.
Reply With Quote
The Following 3 Users Say Thank You to rszmjt For This Useful Post:
Damien (02-18-2021), NorCam (02-18-2021), Xplantdad (02-18-2021)
  #609  
Old 02-18-2021, 10:00 PM
NorCam's Avatar
NorCam NorCam is offline
Senior Member
 
Join Date: Feb 2015
Location: Alberta, Canada
Posts: 4,190
Thanks: 2,583
Thanked 3,399 Times in 1,242 Posts
Default

Hope so. Just waiting on a set of Z/28 frame mounts to come up from the US so I can finally get the motor into the car and mount the shifter and the headers. Full steam ahead after that and hopefully no more delays.
__________________
I like solid lifter cars, big cams and cars w/ 3 pedals in them.
Reply With Quote
  #610  
Old 02-20-2021, 01:47 PM
NorCam's Avatar
NorCam NorCam is offline
Senior Member
 
Join Date: Feb 2015
Location: Alberta, Canada
Posts: 4,190
Thanks: 2,583
Thanked 3,399 Times in 1,242 Posts
Default

Just finishing my coffee before heading out to the shop for the day. Going to finish up the carpet install. swap the clock out for a center fuel gauge, install a new 3967939 heater switch and reinstall the column, boot & carpet shield. After that, I have some gauges and an ignition box to install and prewire ahead of the motor and trans going in.






__________________
I like solid lifter cars, big cams and cars w/ 3 pedals in them.
Reply With Quote
The Following User Says Thank You to NorCam For This Useful Post:
big gear head (02-20-2021)
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 11:59 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

O Garage vBulletin Plugins by Drive Thru Online, Inc.