|
Register | Album Gallery | Thread Gallery | FAQ | Community | Calendar | Become a Paid Member | Today's Posts | Search |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Factory Z28 headers
Does anyone have a picture or description of what factory headers look like? I just picked up a Z that has headers with 4 bolt collectors and 3 piece flanges.
Thanks, Jason |
#2
|
|||
|
|||
Re: Factory Z28 headers
Jerry MacNeish's book shows some of the factory headers. If you are saying that the flange where they bolt to the head is separated between the inner and outer ports, then I don't think they are factory headers. I've got a couple of books at home and I'll check after to work to make sure.
__________________
69 Z28 JL8, #'s match - being restored |
#3
|
|||
|
|||
Re: Factory Z28 headers
According to Jerry's book, the factory headers were built by Thomas and Kustom. Both had flanges that were connected, not 3 part like you describe. The Kustom headers had 4 bolt collectors, the Thomas headers were slip fit and then 3 bolt collector. Here's some pictures of the headers I had Stahl make for me to somewhat duplicate the factory headers.
__________________
69 Z28 JL8, #'s match - being restored |
#4
|
|||
|
|||
Re: Factory Z28 headers
Boy, I bet they were expensive. sam
|
#5
|
|||
|
|||
Re: Factory Z28 headers
They weren't cheap, but they weren't too bad. I think I paid $650 for the pair. Which isn't bad considering there is nothing out there that looks like the factory headers. Charley had a set on the old 67 Z28 he used to have and they looked sweet. Nothing for my car has been cheap so far. I had to pick a really rare and unique project just so it could be really expensive!
__________________
69 Z28 JL8, #'s match - being restored |
#6
|
|||
|
|||
Re: Factory Z28 headers
Ya, You are right about that. My wife always says to me that nothing is ever ok or good enough to me. It has to be the most expensive or you wouldn't do it will you Sam? And I say... only in America, only in America! She then gets mad. Sam
|
#7
|
|||
|
|||
Re: Factory Z28 headers
[ QUOTE ] They weren't cheap, but they weren't too bad. I think I paid $650 for the pair. Which isn't bad considering there is nothing out there that looks like the factory headers. Charley had a set on the old 67 Z28 he used to have and they looked sweet. Nothing for my car has been cheap so far. I had to pick a really rare and unique project just so it could be really expensive! [/ QUOTE ] I agree with Jeff. Ain't nothing cheap for 1st generation cars any more. Years ago, Carl Dwiggins, a early muscle car collector in NC, told me he bought the parts he needed no matter what the cost. Rare or otherwise. He advised me to do the same. Little did I know how right he was!
__________________
Craig S. "I saw Elvis At 1000 Feet" John Force. |
#8
|
|||
|
|||
Re: Factory Z28 headers
Very cool headers where did you find pic's of what they should look like
__________________
69 Z,RS,org,wht. Stripes,wht. Vinyl,wht. houndstooth, fold down rear seat built late Nov.68 (549401) |
#9
|
|||
|
|||
Re: Factory Z28 headers
There are some pictures in Jerry MacNeish's Definitive 67-68 Camaro Z28 book, Wayne Guinn's 2 X 4 Crossram Manual and Martyn Schorr's Camaro book.
__________________
69 Z28 JL8, #'s match - being restored |
#10
|
||||
|
||||
Re: Factory Z28 headers
This is what an NOS set of factory headers looks like. This is the driver's side Bill Thomas style used in '67. Stahl headers do not have the same pipe bends as these but use the same (or similar) style of flange at the cylinder head interface.
-Jon 1967 Z28 street car 1967 Z28 Trans Am race car 1967 Z28 Registry |
|
|