|
Register | Album Gallery | Thread Gallery | FAQ | Community | Calendar | Become a Paid Member | Today's Posts | Search |
|
Thread Tools | Display Modes |
#21
|
||||
|
||||
Still pursuing the Ansen/EELCO acorn style lug nut; 7/8" head, 3/4” shank and 7/16” (RH) threads and 1/2" (RH) threads.
Thanks
__________________
"Day 2 Grocery Getter" 68 SSRS 427 Dana Camaro |
#22
|
||||
|
||||
'
I have a coffee can 'chock full o' nuts' I've been meaning to go though also bottom toolbox drawer I'll check. What of adding one locking style per wheel, even if only temporarily and would an NOS 4-pack like these Eelco nuts on eBay be enough to complete your set? https://www.ebay.com/itm/New-Vintage...-/153465543340 Otherwise, how's things in Winterpeg Dave! Maybe you have it already but here's a pic way below I've been meaning to send you. ~ Pete .
__________________
I like real cars best...especially the REAL real ones! Last edited by PeteLeathersac; 03-13-2021 at 03:38 AM. Reason: LinkFix |
#23
|
||||
|
||||
'
.
__________________
I like real cars best...especially the REAL real ones! |
The Following User Says Thank You to PeteLeathersac For This Useful Post: | ||
68 DANA (07-17-2021) |
#24
|
||||
|
||||
I do have a set of the EELCO locking lug nuts, but when placed among the EELCO acorn style lug nuts they look out of place. There were some on e-bay last week but I missed the listing......dang!
Thanks for the pic.
__________________
"Day 2 Grocery Getter" 68 SSRS 427 Dana Camaro |
#25
|
||||
|
||||
'
Bummer you missed the ones on eBoy, I'll check what's here and ping you if any luck. How many more do you need to complete your set? ~ Pete .
__________________
I like real cars best...especially the REAL real ones! |
#26
|
||||
|
||||
Quote:
I am looking for quantity of 5 (7/16" - RH thread) and 5 (1/2" - RH thread). The Mr.Gasket acorn style version from back in the day are very close but when the two are compared side by side there is a difference. Thanks for keeping you eyes open.....much appreciated!
__________________
"Day 2 Grocery Getter" 68 SSRS 427 Dana Camaro |
The Following User Says Thank You to 68 DANA For This Useful Post: | ||
PeteLeathersac (03-14-2021) |
#27
|
||||
|
||||
Here are some close up pictures for reference. I am not too concern on the length as they can always be turned down if required.
Thanks
__________________
"Day 2 Grocery Getter" 68 SSRS 427 Dana Camaro |
#28
|
||||
|
||||
'
What of adding some LH studs w/ LH nuts as these currently on eBoy... https://www.ebay.com/itm/16407326247...MAAOSwubdePxjR Even if temporary 'til you find more, only you'd know plus it could help thwart theft too? Also, if OSD of 7/16" and 1/2" the same, could you retap 7/16" LH to 1/2" RH? Even tapping 1/2" LH to 1/2" RH may work also if weaker, one @ each wheel Ok? Best of luck w/ your quest! ~ Pete .
__________________
I like real cars best...especially the REAL real ones! Last edited by PeteLeathersac; 08-20-2021 at 11:33 AM. Reason: LinkFux |
#29
|
||||
|
||||
Still searching.....they seem to be hard to locate. Not sure why as many speed shop sold them back in the day. You can find Ansen rims but are usually without the lug nuts.
__________________
"Day 2 Grocery Getter" 68 SSRS 427 Dana Camaro |
#30
|
|||
|
|||
Last edited by 3X24SPD; 10-27-2021 at 08:08 PM. |
|
|