|
|
|
#1
09-04-2017, 10:46 PM
|
||||
|
||||
'69 Camaro mirror
Does anyone make a good driver's door mirror for a '69 Camaro that will stay put? Mine just flops down when I take off hard or when I'm at freeway speeds. I've been told that all of the reproductions are that way.
__________________
Freddie 1969 Camaro RS/SS396 (427) 4 speed 
|
|
#2
09-05-2017, 12:39 AM
|
|||
|
|||
|
Have you tried the local Chevy dealer? Don't know if it's still available or assembly line correct but it was a couple of years ago and looked good.
Dustin
|
| The Following User Says Thank You to bluel78 For This Useful Post: | ||
big gear head (09-05-2017) | ||
|
#3
09-05-2017, 02:07 AM
|
||||
|
||||
|
__________________
...................... John Brown This isn't rocket surgery.....
|
| The Following User Says Thank You to John Brown For This Useful Post: | ||
big gear head (09-05-2017) | ||
|
#4
09-05-2017, 10:37 AM
|
||||
|
||||
|
Freddie these aren't the cheapest, but I've heard good things about them:
https://www.morrisclassic.com/collec...angularmirrors
__________________
Tim in NSW, Australia 1969 Van Nuys 04A Z/28 from Clippinger Chevrolet. Cortez Silver with dark blue interior. Ran at Lions Dragstrip and Pomona Raceway, with paint by Bob Kovacs of Fresno.
|
| The Following User Says Thank You to ZLP955 For This Useful Post: | ||
big gear head (09-05-2017) | ||
|
#5
09-05-2017, 12:06 PM
|
||||
|
||||
|
Thanks guys. I'll look into all of these.
__________________
Freddie 1969 Camaro RS/SS396 (427) 4 speed
|
|
#6
09-05-2017, 11:05 PM
|
|||
|
|||
|
I bought a pair of morris classic mirrors for the beater El Camino. No regrets. They stay put.
__________________
Don't believe everything you read on the internet ... Ben Franklin
|
| The Following User Says Thank You to Lynn For This Useful Post: | ||
big gear head (09-05-2017) | ||
|
#7
09-06-2017, 12:43 AM
|
||||
|
||||
|
I bought a reproduction mirror for my Chevelle years ago and it was loose. The dealer told me to set the mirror at the desired angle, take it back off the door, place it face down on a table and then run a bead of super glue around the ball joint. You don't see the glue and it has stayed put for over 15 years. It works for me.
__________________
Robert _______________ 1969 Chevelle SS396 L78 M21 4.10 2023 Stingray Coupe Z51
|
| The Following User Says Thank You to tunes For This Useful Post: | ||
big gear head (09-06-2017) | ||
|
#8
09-11-2017, 08:36 PM
|
||||
|
||||
|
I bought one of these from Paragon a few years back. It's still tight. And they will date it as well.
https://www.paragoncorvette.com/p-35...mirror-lh.aspx
|
| The Following User Says Thank You to parkbrau For This Useful Post: | ||
big gear head (09-11-2017) | ||
|
#9
09-11-2017, 09:24 PM
|
|||
|
|||
|
I've had the same problem with my 1966 Corvette. The mirror on it when I bought it would not stay put. Bought a new one from one of the Corvette suppliers and it was the same out of the box. I removed the glass from one to try and tighten it but it did not have screws to tighten the ball. Ended up buying a cheap plastic one at an auto parts chain store. This one works but the does not fit correct but it will do for now.
The Morris mirrors look like a good option but I don't need a pair.
__________________
Dave 1970 Monte Carlo SS
|
| The Following User Says Thank You to drdave69 For This Useful Post: | ||
big gear head (09-11-2017) | ||
|
#10
09-11-2017, 11:26 PM
|
||||
|
||||
|
Dave I'm kind of like you. I don't really need 2 mirrors. I have been thinking of going ahead and getting them both and putting the right one on, but I hate to start drilling holes in my door. I might try the Paragon mirror.
__________________
Freddie 1969 Camaro RS/SS396 (427) 4 speed
|
| The Following User Says Thank You to big gear head For This Useful Post: | ||
bluel78 (07-23-2018) | ||
 |
|
|
Linear Mode
