Go Back   The Supercar Registry > General Discussion > Day 2 stuff-modified cars


Reply
 
Thread Tools Display Modes
  #1  
Old 02-28-2021, 03:18 PM
Gonzo1717 Gonzo1717 is offline
Yenko Contributing Member
 
Join Date: Jan 2019
Location: Southern Ca
Posts: 129
Thanks: 12
Thanked 10 Times in 6 Posts
Default Square tube traction bar install issues, any experts?

While installing my “grumpy bars” on my 69 camaro, with 12 bolt and multileaf, I ran into an issue. I installed the large wedges (4 degree early wide style) without the lower insulator.

Once I got everything bolted up, I noticed there was a severe front to back “rock” on the differential despite all the bolts being tightened (see red circles in picture). It appeared as if the wedge created a gap 1/4” between the front spring perch insulator and spring (see green arrow on picture).

My question is, do I install the lower insulator with the wedge? If not, how to I remedy this front and back motion?

My assumption is that the lower insulator must be installed, I just couldn’t see how the assembly would stay “located” with the alignment pin from the lower portion of the leaf through the insulator, wedge, and down into the traction bar hole.

I decided to bolt it together, without the wedges, utilizing the lower spring insulator and it worked great. Unfortunately, this manner of installation isn’t possible because the bars hang far too low to the ground (see picture) and have a tremendous amount of gap between the snubber and the leaf. My understanding is that 1/2” gap is the max you should run.

I am also looking for any input as to correct “adjustment” of these bars for best performance.

Thanks in advance for any input!
Attached Images
   

Last edited by Gonzo1717; 02-28-2021 at 03:24 PM.
Reply With Quote
Attachments - The Supercar Registry 84B9E416-DCE8-41DF-ACE1-D8A6B78AACEC.jpeg 34E772B5-59CE-485C-8403-3E4A03AE9DB2.jpeg 037AA0E2-D057-4BC3-B4FB-DF46D69C24B3.jpeg
Click here to view all the pictures posted in this thread...
  #2  
Old 03-17-2021, 09:58 AM
Day2_69Z Day2_69Z is offline
Yenko Contributing Member
 
Join Date: Dec 2012
Location: Western Pa.
Posts: 1,368
Thanks: 3
Thanked 17 Times in 11 Posts
Default

I can sure use a pair of the same kinda wedges you're inquiring about adjustment.
__________________
Day Two Specialties /High Quality Muscle Car Parts.
Reply With Quote
  #3  
Old 03-17-2021, 06:32 PM
Chuck_Burg's Avatar
Chuck_Burg Chuck_Burg is offline
Yenko Contributing Member
 
Join Date: Feb 2019
Location: Long Beach, CA
Posts: 284
Thanks: 180
Thanked 318 Times in 117 Posts
Default

Gonzo, in the past when using shims I've always installed them on top, between the perch and spring. This makes a much tighter fit. Copy and paste the link below for your reading pleasure...

https://www.jegs.com/InstallationIns.../620-21150.pdf
Reply With Quote
  #4  
Old 03-17-2021, 07:03 PM
chevyandpontiac chevyandpontiac is offline
Yenko Contributing Member
 
Join Date: Apr 2010
Location: Shorewood, IL
Posts: 753
Thanks: 56
Thanked 250 Times in 124 Posts
Default

When I have installed mine, working from the traction up.

This is just my .02

traction bar
Aluminum wedge
Lower pad with the nub
leaf spring
upper pad with the notch.

Then I impact them evenly.

With a 4 degree wedge I wouldn't think it would still be that low in front
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 11:28 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.