Forum: Supercar/Musclecar Discussion
Yesterday, 03:01 AM
|
Replies: 62
Views: 35,334
Crankshafts for 430 were:
P#3993803 Machined...
Crankshafts for 430 were:
P#3993803 Machined 3.47 stroke
P#3965746 Semi-Finished 3.4 to 3.8.
Another Semi-Finished one was available, but will have to search down that unit part number meant for...
|
Forum: Supercar/Musclecar Discussion
09-23-2024, 06:41 PM
|
Replies: 62
Views: 35,334
|
Forum: Pontiac
09-22-2024, 02:21 AM
|
Replies: 109
Views: 77,492
|
Forum: Lounge
09-19-2024, 10:35 PM
|
Replies: 15
Views: 903
|
Forum: Dick Harrell
09-19-2024, 01:28 PM
|
Replies: 6
Views: 590
'68 Dick Harrell Nova L88
I have 60 classified ads for Dick Harrell cars in an excel spreadsheet and have been attempting to locate the folks (or kin) who had these cars.
I located David who told me his incredible story of...
|
Forum: Olds
09-19-2024, 12:47 AM
|
Replies: 3,317
Views: 3,811,776
|
Forum: Olds
09-19-2024, 12:30 AM
|
Replies: 3,317
Views: 3,811,776
|
Forum: Lounge
09-17-2024, 10:27 PM
|
Replies: 15
Views: 903
Lifts
Asemmetrical lifts are handy , advantage to symmetrical is you can point vehicle either way if that is a consideration .
|
Forum: Lounge
09-17-2024, 09:41 PM
|
Replies: 15
Views: 903
|
Forum: Lounge
09-17-2024, 09:02 PM
|
Replies: 15
Views: 903
|
Forum: Garages/shops..
09-17-2024, 08:56 PM
|
Replies: 32
Views: 14,336
|
Forum: Lounge
09-17-2024, 08:49 PM
|
Replies: 15
Views: 903
|
Forum: L78/L89 specific Forum
09-17-2024, 07:52 PM
|
Replies: 94
Views: 46,109
... more photos
...
... more photos
https://www.yenko.net/forum/picture.php?albumid=141&pictureid=1133
https://www.yenko.net/forum/picture.php?albumid=141&pictureid=1128
... y
|
Forum: L78/L89 specific Forum
09-17-2024, 07:48 PM
|
Replies: 94
Views: 46,109
... More recent photos
...
... More recent photos
https://www.yenko.net/forum/picture.php?albumid=141&pictureid=1125
https://www.yenko.net/forum/picture.php?albumid=141&pictureid=1126
|
Forum: Lounge
09-17-2024, 06:17 PM
|
Replies: 15
Views: 903
I have a Worth Equipment 7000lb floor plate...
I have a Worth Equipment 7000lb floor plate model.
Quality of the lift is great, and it's made in USA.
I bought it used, so it was about half price of new.
I use it almost daily for my own...
|
Forum: Garages/shops..
09-17-2024, 05:43 PM
|
Replies: 32
Views: 14,336
|
Forum: Yenko Chevrolet
09-12-2024, 05:33 PM
|
Replies: 4
Views: 861
1969 Yenko Camaro Engine Found.
I have known about this engine for more than 15 years, it was advertised for sale in Phillipsburg, PA as a COPO engine stamped T0304MN. Since I recently bought a 69 triple black X44 D80 COPO, I was...
|
Forum: Day 2 stuff-modified cars
09-12-2024, 01:02 AM
|
Replies: 164
Views: 117,425
Hello everyone,
Have to chime in here and...
Hello everyone,
Have to chime in here and tell you all that my son and I dropped into Illinois on the September long weekend, and we finally got to meet up with Dan Reimer. Not only was he a great...
|
Forum: Day 2 stuff-modified cars
09-11-2024, 02:12 PM
|
Replies: 16
Views: 1,964
|
Forum: Lounge
09-11-2024, 01:14 PM
|
Replies: 6
Views: 694
911...
Lest we forget :flag: :flag: :flag:
|
Forum: Garages/shops..
09-08-2024, 04:35 AM
|
Replies: 32
Views: 14,336
The coated floor was a new pour that had cured...
The coated floor was a new pour that had cured for a few months.They initially did a urethane coating that failed almost right away because the chemical company sent them the wrong chemicals. The...
|
Forum: L78/L89 specific Forum
09-08-2024, 04:07 AM
|
Replies: 400
Views: 242,250
|
Forum: Garages/shops..
09-08-2024, 02:12 AM
|
Replies: 32
Views: 14,336
|
Forum: Supercar/Musclecar Discussion
09-06-2024, 09:06 PM
|
Replies: 114
Views: 61,578
That's exactly what I did. I incorrectly called...
That's exactly what I did. I incorrectly called the lower bearing housing "plastic end piece". I pressed the old bearing out of the lower bearing housing, using a brake cylinder hone I opened it up...
|
Forum: Supercar/Musclecar Discussion
09-05-2024, 11:11 PM
|
Replies: 114
Views: 61,578
Here is What I used: ...
Here is What I used:
https://www.ss396.com/camaro/FBK-678.html
The Bearing is encapsulated into the Lower Bearing Housing, I never thought about extracting the Bearing ONLY and re encapsulating...
|