Dedicated to the Promotion and Preservation of American Muscle Cars, Dealer built Supercars and COPO cars. |
|
#1
12-22-2008, 12:45 AM
|
|||
|
|||
Rivet question
ElCamino vent windows, are held to the frame with a small rivet. This is the rivet that is sold to replace the one I had to drill out to remove the glass/chrome frame. The end is hollow. Does anyone know how to install/crimp this rivet? Special tool? Certainly not any type of rivet, I've used.
 
|
|
#2
12-22-2008, 05:01 PM
|
||||
|
||||
|
Re: Rivet question
Bill
Yes they required a special die for the hollow end. Then they were squeezed. Same as a riveted brake shoe. Sorry I can not help on th tool. Are the rivets you bought stainless steel or plated steel ? Mike
|
|
#3
12-22-2008, 05:45 PM
|
||||
|
||||
|
Re: Rivet question
Bill....nice woodgrain on the furniture
__________________
02 Berger 380hp #95 Lots of L78 Novas Join National Nostalgic Nova! 70 Orange Cooler 69 Camaro
|
|
#4
12-22-2008, 06:15 PM
|
||||
|
||||
|
Re: Rivet question
Does anyone have a photo of a crimped one? Then we could figure out what would be required to form the new one...
Probably something with a male die to go into the end of the rivet a short chamfer to roll the rivet...
__________________
~JAG~ NCRS#65120 68 GTO HO 4 spd Alpine Blue /Parchment 2 owner car #21783 71 Corvette LT1 45k miles Orig paint - Brandshatch Green - National Top Flight - last known 71 LT1 built. 71 Corvette LT1 42k miles Original paint - Black - black leather - only black LT1 known to exist. NUMEROUS Lemans blue Camaros, Monza Red and Daytona Yellow Corvettes & a Chevelle or two... Survivors, restored cars, & other photos https://picasaweb.google.com/lh/myphotos
|
|
#5
12-22-2008, 07:20 PM
|
|||
|
|||
|
Re: Rivet question
Look up (Hanson Rivet) on-line they have the rivets and the tools to crimp them .
__________________
"Knowledge is good" Emil Fabor 67 L/78 Camaro SS/RS H-H,1W,2LGSR,3SL,4K,5BY. (Sold) 70 L/78 Nova M-21,Black Cherry,Sandalwood Int. 09 Pontiac G8 GT Premium,Sport,Roof. Liquid Red.
|
|
#7
12-22-2008, 10:48 PM
|
|||
|
|||
|
Re: Rivet question
You can also try www.rivetsinstock.com That's the website for jay-cee sales and rivet co. They have just about any rivet you can think of and also stock the tubular set tool shown.
Chris
|
|
#8
12-23-2008, 01:28 AM
|
||||
|
||||
|
Re: Rivet question
Bill
These guys have the rivet sets too. http://www.hansonrivet.com/w83.htm There made for a rivet squeezer, but for a one time application you might insert the die into a piece of round stock and lightly form the shop head by hand with a hammer. Mike Dha....They also have these.... http://www.hansonrivet.com/w78.htm Mr. Edit Guy 
|
|
#9
12-23-2008, 02:41 AM
|
|||
|
|||
|
Re: Rivet question
I never knew there was so much to know about rivets/rivet tools. I think I have all the info I need. Thanks for the responses.
|
|
#10
12-23-2008, 03:17 AM
|
||||
|
||||
|
Re: Rivet question
[ QUOTE ]
Here's a picture of what they look like, tubular rivet tool  [/ QUOTE ] That is the precise tool I had imagined in my head... trippy... da ding ding zzz da ding ding zzz....
__________________
~JAG~ NCRS#65120 68 GTO HO 4 spd Alpine Blue /Parchment 2 owner car #21783 71 Corvette LT1 45k miles Orig paint - Brandshatch Green - National Top Flight - last known 71 LT1 built. 71 Corvette LT1 42k miles Original paint - Black - black leather - only black LT1 known to exist. NUMEROUS Lemans blue Camaros, Monza Red and Daytona Yellow Corvettes & a Chevelle or two... Survivors, restored cars, & other photos https://picasaweb.google.com/lh/myphotos
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
