Dedicated to the Promotion and Preservation of American Muscle Cars, Dealer built Supercars and COPO cars. |
|
|||||||
| Register | Album Gallery | Thread Gallery | FAQ | Community | Calendar | Become a Paid Member | Today's Posts | Search |
|
|
|
Thread Tools | Display Modes |
|
#1
10-11-2024, 02:22 PM
|
|||
|
|||
Compressed Air Piping
Hi everyone. Looking for advice on the best air piping to use for garage compressed air system. I would like to conceal in the walls and above the ceiling for the installation method. What is everyone using?
Thanks! Bob 
|
|
#2
10-11-2024, 02:53 PM
|
||||
|
||||
|
I used black iron pipe throughout the garage also behind the walls. I used T111 exterior siding inside held on with sheet rock screws. I collect signs so that's why the siding. The screws so you can get in there if you need to. It's been 12 years & no problems. I also ran the electrical behind but mounted it about chest high in case something was stacked on the floor....Joe
__________________
1968 Z/28 Corvette Bronze. Black Hounds Tooth. 02E Los Angeles born 3/13/1968 pnt OO 1969 SS396 Yellow/Yellow 08E Norwood born 8/28/1969 pnt 76E 1970 'cuda Moulin Rouge, 440-6, 4 speed
|
| The Following 2 Users Say Thank You to X66 714 For This Useful Post: | ||
69M22Z (10-11-2024), big gear head (10-11-2024) | ||
|
#3
10-11-2024, 04:09 PM
|
||||
|
||||
|
Black iron because it acts like a cooling agent, where plastic, or rubber insulates. I had a diagram I posted before that shows the proper routing and drops, but I can't find it now.
__________________
WOT
|
|
#4
10-11-2024, 04:35 PM
|
||||
|
||||
|
My "Rapid-Air" Plastic system has Constant issues, Sad I went this route now.
"MAXLINE" system.
__________________
69 Los Z11 68 SS/RS 396/325 68 Los Z28 
|
|
#7
10-11-2024, 06:19 PM
|
||||
|
||||
|
I ran all the piping high & when it stubs out at the wall each one has a ball valve shut off & also a drain about a foot below the tee coming out of the wall....Joe
__________________
1968 Z/28 Corvette Bronze. Black Hounds Tooth. 02E Los Angeles born 3/13/1968 pnt OO 1969 SS396 Yellow/Yellow 08E Norwood born 8/28/1969 pnt 76E 1970 'cuda Moulin Rouge, 440-6, 4 speed
|
|
#8
10-11-2024, 08:01 PM
|
||||
|
||||
|
Quote:
What he said.
__________________
WOT
|
|
#9
10-11-2024, 09:43 PM
|
|||
|
|||
|
----Not kosher, but when I built my cave we buried the lines in the walls. My suggestion is that if you have anything behind a wall be sure to triple test the system. I now have to shut off mine at night, which isn't too big a deal. I have so much crap in front of the walls that I just can't imagine trying to fix the minor leak I have. If I forget it takes several hours to blead down....Bill S
|
|
#10
10-11-2024, 10:21 PM
|
||||
|
||||
|
I used the Rapid Air Rapid Pipe (aluminum pipe) about 5 years ago. I'm really happy with the product. I myself would be a bit skeptical about being sandwiched in the wall in the event of a leak or failure.
https://www.rapidairproducts.com/sho...-ft-master-kit Nonetheless, the fittings were high quality and the system it easily added on to. Tim
|
|
|
|
Linear Mode
